1.After the transmitter has lost power for any reason, the receiver is working for three cycles, the time is about 12 minutes, and the receiver stops working after 12 minutes.A reincarnation means: 3 minutes static & beep mode and 1 minute beep mode (1 minute only beep mode), like this 3 times after the receiver collar stops working.
2.The max. range is up to 500 meters and min. range is 20 meters from transmitter.
3.100 levels of intensity with no jump step for remote range adjustment.
4.Pulsed proportional stimulus–closer your dog gets to the boundary,more intense it’ll be.
5.Progressive tone stimulus–a warning tone first and then stimulate if your dog would not stop move to the boundary.
3.Material: ABS(Acrylonitrile Butadiene Styrene)
6.Transmitter Size: 16.5x14x3.5cm
7.Receiver Size: 7x4x3.5cm
8.Strap Size: 73x2cm
9.Neck Circumference: 20-56cm
10.Waterproof Level: IPX6
11.Plug Type: US Plug
Step 1: Turn on the transmitter by pressing ON/OFF button for 3 seconds.
Step 2: Power Level Adjustment: press the button “+” or “-” for the adjustment of transmitting power level, with a purpose to change the remote keep watch over range of this system. Press button “+” to increase the power level(The max. value is level 100.), press button “-” for level decrease.(The min. value is 0.)
Step 3: Make sure the transmitter is on, then press on/off button shortly to go into cording status. The screen will display “1dp” with flashing.
Step 4: The transmitter will have to be powered by AC adapter, which the output is 5V/1A.
1x Transmitter(The dog not included)
1x Power Cord
1x User Manual
1x Operating Guide
1x Voltage Tester
4x Bark Stopper
2x Rubber Stopper
FOCUSPET WIRELESS PET FENCE SAFE&EFFECTIVE — FOCUSPET Invisible fence is completely protected and harmless to your pet,if the dog is beyond the setting distance, the receiver collar will start up by a warning tone, then static shock until your dog comes back to “safety zone” ,an unlimited number of receivers supported at same time.Please install the transmitter 1.5 meters away from the ground and no metal wall, so as not to interfere with the wireless signal, affecting the remote keep watch over distance.
DOG CONTAINMENT WIRELESS FENCE COLLAR RECEIVER — Receiver collar with automatic sleep function, lithium battery is 300 mA,about 12 hours’ standby time , full of electricity normal use is about 8-9 hours.Waterproof and rechargeable collar receiver,the collar fits dogs 8 pounds and up with neck sizes from 6 to 26 inches (Small/Medium/Large/Extra Large Dogs),The static mode of the collar is protected and harmless to your pet.
LEVEL 1-100 UP TO 500 METERS RADIUS AT MAX SETTING — Do not touch the two screws on the collar before connecting the receiver and the transmitter, it is best to stuck the test light on the two studs before turning on the power, and if there is an electric light, do not touch the electric screw for not being mistakenly touched by the electric shock.
EASY FOR CODING — First start the transmitter and then receiver start, short press the transmitter ON / OFF button, the transmitter into the code state, digital display “1dp” and flashing, the code duration of 7 seconds, then press the receiver power button So that the receiver also entered the code state, the receiver red light long, on the issue of “B” sound at the same time as the blue light flash once, said the success of the code.The usage of Procedure: Turn on the transmitter – Turn on the transmitter to pair
NOTICE — 1.Proper fit of the collar is important. Too long or made too tight on the pet’s neck may cause skin damage. 2.Avoid leaving the collar on the dog for more than 12 hours per day.When imaginable reposition the collar on the pet’s neck every 1 to 2 hours.Check the fit to prevent excessive pressure.3.The receiver collar must be closed before cutting off the transmitter power4.NEVER perform set-up procedures when the collar is on your dog.5A low battery may cause intermittent operation.